Sevigny Competition Glock Sights
  • Sevigny Competition Glock Sights
  • Sevigny Competition Glock Sights
  • Sevigny Competition Glock Sights

Sevigny Competition Glock Sights

$76.95
Select Sight Set Desired
Quantity

We are discontinuing the Warren/Sevigny products.  Once these are gone we will not be restocking them.

This is the sight set Dave Sevigny used to win the 2005 IDPA Nationals and both the Production and Limited-10 USPSA Nationals.  This design is competition proven...crisp and clean.  Two sets are available, with different front sight heights.  Choose from a plain rear, serrated front option, or a plain rear, fiber optic front option.  You also have options for either the narrow .130 width or standard competition .150 width rear notch.   

Price is $76.95 for the plain/serrated combo, and $86.95 for the plain/fiber optic combo.   

Warren Tactical and Sevigny competition and carry sight sets Glock pistols.  All Glock model Warren Tactical and Sevigny sights are designed for a twenty yard point of aim/point of impact.  

Warren Tactical's recommendation is to use the .245 tall front with Gen 4 or Gen 5 guns, Glock 24, 34, 35, and other long slide guns Gen 3 guns, and the .215 tall front for all other Glock models, when mated with a Warren or Sevigny rear.  

You can't use a Warren/Sevigny .215 or .245 front with a factory Glock rear sight.   Warren/Sevigny front sights DO NOT extend beyond the slide cut-out on model 34 or 35 pistols, but will extend out a bit on the MOS guns.

Remember that Glocks are production guns, so there could be slight variations in each of them, and point of aim/point of impact is further affected by ammo differences, bullet weight differences, shooter tendencies, etc.   

All Warren/Sevigny sights should be installed by a certified Glock armorer or gunsmith. 

Don't forget that we offer a sight installation service for Glock sights. See below.

Here are some basic pointers to help with sight selection for glock pistols:

Standard rear sight notch width is .150″ and generally provides the best window for both speed and accuracy.

Applications: Carry weapons, GSSF, Pro-Am, Steel Challenge and USPSA/IPSC pistols.

We also offer a narrow .130” rear sight notch width. This creates a tighter sight picture to suit preferences of those competing in accuracy intensive disciplines.

Applications: Bullseye, GSSF, NRA Bianchi Cup, PPC, Target pistols.

The front sights for Glock pistols are available in .215″ and .245″ tall heights.

Competition Plain and Fiber Optic front sights are .115” wide.

Carry Plain and Tritium front sights are .125” wide.

Point of Aim/Point of Impact (POA/POI) for G34 and G35, with most subsonic ammo, will be at or slightly above the front post (approx. 2”) with the .215″ tall front at 25 yards.

In general, 115 grain and 125 grain 9×19 ammo fired from a G34 and 155 grain and 165 grain .40 fired from a G35 will print higher than 2” and is why a .245” tall front should be selected for this type of ammo.

POA/POI with G17, 19, 20, 21, 22, 23, 26, 27, 29, 30, 31, 32, 33, 36, 37, 38 and 39 pistols is correct with a .215” tall front.

ALL G17L and G24 pistols should use a .245″ tall front for best POA/POI.

Technical Specifications

Sevigny Competition

Front Sight: .115" wide x .215" tall, 70 LPI serrations, black oxide finish, 3/16" hex screw retention

Rear Sight: .150" wide x .120" rear notch, flat back drafted surface (no distracting points, edges or serrations) with nominal 1/8" radii corners, hardened steel, black oxide finish, dovetail press fit and stainless set screw for back-up retention

Made in the USA, PATENTED

Drift adjustable rear only

Installation recommended by a qualified gunsmith only.

Sevigny Competition w/fiber optic front sight

Same as the "Competition", with a fiber optic front sight.  When heated, the 1mm fiber optic rod melts to a 1/16 th of an inch diameter.  The top of the rod diameter and top of the front sight appear flush when aiming.

Front Sight: .115" wide x .215" tall, 70 LPI serrations, 1mm fiber optic through diameter with a .060" front counterbore, black oxide finish, 3/16" hex screw retention.  Green and Red, 1mm (.040") fiber optic rod included, approx. 2 ½" long

Rear Sight: .150" wide x .120" rear notch, .250" tall, flat back drafted surface (no distracting points, edges or serrations) with nominal 1/8" radii corners, hardened steel, black oxide finish, dovetail press fit and stainless set screw for back-up retention

Made in the USA, PATENTED

Drift adjustable rear only

Installation recommended by a qualified gunsmith only.

048-007A
4 Items
New product

You might also like